Holybro Kopis Mini Analog VTX Version 148.6mm F7 3 Inch FPV Racing Drone PNP BNF

Specification:
Brand Name: Holybro
Model: Kopis Mini ( Analog VTX Version)
Item Name: 148.6mm F7 3 Inch FPV Racing Drone

Frame:3mm 3K Ccarbon Fiber
Wheelbase: 148.6mm

Flight Controller: Kakute F7 V1.5

ESC:Tekko32 F3 4in1 45A mini ESC

VTX: Atlatl HV V2

Motor: F1507 KV3800

Propeller: T3140

FPV camera: 1200TVL Foxeer Micro Razer FPV Camera
Receiver: Without Receiver / Frsky R-XSR Receiver ( Optional)

Adjustable camera uptilt from 0 degrees to 90 degrees

Buzzer included.

Battery plug: XT30

Weight:173g

Recommend Battery: 4S 650mAh~1300mAh Lipo ( NOT Included)

olybro Kakute F7 V1.5 Flight Controller ( More Details)	MCU: STM32F745 32-bit processor ( Manual) IMU: MPU6000 (SPI) Barometer: BMP280 Current Sensor: Approximately 130 amps maximum measurable value USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 6 hardware UARTS (UART1,2,3,4,6,7) All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”. Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. TF card for Blackbox logging Dimensions: 35x41x7mm (includes foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 8g
Tekko32 F3 4in1 45A mini ESC ( More Details)	Brand Name: Holybro Model: Tekko32 F3 45A Item Name: 45A BLheli_32 3-6S 4 in 1 ESC Con. Current: 45A Peak Current: 50A - F3 MCU, runs double faster than F051 - 32bit ESC with BLHELI32 firmware - Supports 3-6S lipo input -PWM input, TLM supported - Voltage output (VBAT) - NO BEC - Supports oneshot / Multishot / Dshot PWM - Supports damped light - Ext. cap needed for 6s (470uf 35v for 6s usage.) - Mounting holes M2, 20x20mm - Size:30 x 36 mm - Weight: 7.8g
T-Motor F1507 3800KV Motor ( More Details)	Brand Name: T-Motor Model: F1507 KV: 3800KV Input Voltage: ( Lipo) 3-4S Configuration: 12N14P Shaft Diameter: 2mm Idle Current ( 5V): 0.9A Peak Current (60s): 23A Max. Power: 372W Internal Resistance: 81mΩ Lead: 24#AWG 100mm Dimension: 18.9x29.7mm Weight: 15g ( Include Cable)
Holybro Atlatl HV V2 FPV Transmitter ( More Details )	Brand Name: Holybro ( VTX Manual) Model: Holybro Atlatl HV V2 Transmitting Output Power: 25mW/ 200mW/ 500mW/ 800mW Switchable Audio: 6 MHz + 6.5 MHz Mono Antenna Connector: MMCX Input Voltage: 7-28V (2-6S Lipo) Dimension: 35(L)x 25(W)x 7(H)mm Mounting Hole: 30.5x30.5mm Weight: 9.3g

Features:
MCU: STM32F745 32-bit processor
IMU: MPU6000 (SPI)
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging

Package Included:

1x Kopis mini FPV racing drone

4x T3140 Propeller

1x Protective Case Mount for GoPro Hero5

1x Carying case

1x Battery strap(installed)