Matek F405-miniTE

FC Specifications

• MCU: STM32F405RGT6
• IMU: ICM42605
• OSD: AT7456E
• Baro: Goertek SPL06-001 (I2C)
• Blackbox: 16M-byte Flash memory
• 6x UARTs, 1x Softserial_Tx option
• 12x PWM outputs (8x Dshot)
• 1x I2C
• 4x ADC (VBAT, Current, RSSI, Airspeed)
• 2x PINIO
• 1x SH1.0_8pin connector (Vbat/G/Curr/R3/S1/S2/S3/S4)
• 1x SH1.0_6pin connector for DJI FPV Air Unit
• 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)

• Dual BEC, 5V 1.7A & 10V 1.4A
• 10V output ON/OFF switchable
• Convertible 20mm to 30.5mm mounting

Power

• Input: 6~30V (2~S LiPo)
• BEC: 5V 1.7A, Max.2A
• BEC: 10V 1.4A for VTX or DJI Air Unit
• Battery Voltage Sensor: 1K:20K (INAV scale 2100, BF scale 210)
• No Current Sensor built-in, supports external current sensor of PDB/4in1

Firmware

• ArduPilot: MatekF405-TE
• INAV: MATEKF405TE
• BetaFlight: MATEKF405TE

Physical

• Mounting
  • 20 x 20mm/Φ3mm with Silicon Grommets
  • 20 x 20mm/Φ2mm with Silicon & Brass Grommets
  • 30.5 x 30.5mm/Φ3mm with Conversion Plate and Silicon Grommets
• Dimensions: 28 x 28 mm
• Weight: 5g

Including

• 1x FC F405-miniTE
• 1x 20mm to 30.5mm conversion plate(blue PCB)
• 6x Silicon grommets M4 to M3
• 6x Brass grommets M3 to M2
• 1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC
• 1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit

• If sending highspeed serial data (eg. 921600 baud) to the board, use USART1(Serial1) or USART2(Serial6).

Frsky Smartport Telemetry

• non-inverted (hacked) S.Port signal

• any spare Uart_TX
• SERIALx_BAUD 57
• SERIALx_OPTIONS 7
• SERIALx_PROTOCOL 4 or 10(for yaapu)

DJI FPV OSD (ArduPilot 4.1)

https://ardupilot.org/plane/docs/common-msp-osd-overview.html

• OSD_TYPE = 3
• SERIAL4_PROTOCOL = 33
• MSP_OPTIONS = 0 (polling mode)

Relay(PINIO)

• PINIO_1, 10V On by default
• PINIO_2, PB5 pad, spare

# GPIOs

• PA4 PINIO1 OUTPUT GPIO(81) LOW //10v power switch
• PB5 PINIO2 OUTPUT GPIO(82) LOW //spare

# RCx_OPTION: RC input option

• 28 Relay On/Off
• 34 Relay2 On/Off
• 35 Relay3 On/Off
• 36 Relay4 On/Off

e.g.

• RELAY_PIN 81 //10V switch PINIO
• RC7_OPTION 28 //Relay On/Off, Use CH7 of Transmitter to control 10V ON/OFF
• RELAY_PIN2 82 //spare
• RC8_OPTION 34 //Relay2 On/Off, Use CH8 of Transmitter to control high/low level on PB5 pad

The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.

Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.

ArduPilot

• ArduPilot firmware, 8x DSHOT on S1~S8 without DMA clash.
• Support 5V passive buzzer
• Download latest ArduPilot firmware from our website before PR is merged.

INAV

• Known issues: INAV firmware, S3, S5,S7 DSHOT not working because of unknown DMA bug, pls use ONESHOT or MULTISHOT for now.
• Support 5V passive buzzer
• Download INAV firmware from our website before PR is merged.

BetaFlight

• BetaFlight firmware, 8x DSHOT with RPM filter on S1~S8 without DMA clash.
• Support 5V passive buzzer
• ICM42605 has been supported by BataFlight 4.2 or newer, but it is not supported in unified target for now. We can’t add MATEKF405TE target until BF unified target support this new IMU.
• Pls download BF firmware from our website, click “Firmwares” button at upper right corner.
• Barometer SPL06-001 is not supported by Betaflight.