The Lumenier LUX F7 Ultimate + Razor LED 55A Bundle is ultimate FC and ESC combo for your drone. The powerful F7 flight controller allows for simultaneous processes to be handled with ease, giving you a stable and clean signal to your sensors, while the advanced BLHeli_32 Razor LED ESC provides incredibly power and performance, and provides RGB LED lighting at the same time!

This is a plug-and-play system that is guaranteed to work together. The ESC and Flight controller's 8pin connector match up so you don't have to do any re-pinning of cables. Simply plug them in together and you're good to go!

Optionally you can add RGB LED lighting that is powered by the Razor LED 55A ESC for a complete LED lighting system on your drone. Changing colors and patterns is as easy as a push of the button.

Save 5% when buying these items as a bundle compared to buying separately!

Lumenier LUX F7 Ultimate Flight Controller (Dual Gyros)

Features

MCU: 216MHz STM32F722RET6
IMU: MPU6000 & ICM20602, Dual Gyros built-in
Baro: BMP280
OSD: AT7456E
Blackbox: MicroSD card slot
Anti-Vibration silicone grommets built in
5x Uarts (1,2,3,4,6) with built-in inversion
1x Softserial supported
8x Dshot/Proshot/oneshot outputs
1x I2C
1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
Vbat filtered output power for VTX, switchable via AUX (modes tab-user1)
Dual Camera image switchable via AUX (modes tab-user2)
Camera control
Smartaudio & Tramp VTX protocol support
WS2812 Led Strip support
Beeper solder pad
RSSI solder pad
INAV analog airspeed
Input: 6~36V (2~8S LiPo)
BEC: 5V 2A cont. (Max.3A)
LDO 3.3V: Max.200mA
Current Sensor: No
Battery Voltage Sensor: 1:10

Software/Hardware Features

Betaflight support - target MATEKF722SE
BLHeli passthrough flashing supported by hardware
iNav support - target MATEKF722SE

Downloads

Specifications

High quality, gold plated PCB
Micro USB connector for programming
Dimensions: 36x36x6mm (includes USB in height)
Mounting Holes: 30.5mm square to center of holes
Weight: 6g

Includes

1x Lumenier LUX F7 Ultimate Flight Controller
6x Anti-vibration silicone grommets (for M3 sized screws)
1x 8pin micro JST-SH 5cm connector, 1x 6pin connector

Lumenier Razor LED 55A 4-in-1 F3 BLHeli_32 2-6s ESC

The Lumenier Razor LED 55A 4in1 F3 BLHeli_32 2-6s ESC is a 32bit ESC running the latest gen. BLHeli_32 firmware, and featuring future proof powerful F3 processors. Now 4 of these ESCs combine to have more processing power than your whole flight controller! The 32bit architecture enables the ESC to run at incredible speeds resulting in better performance, faster input signals and lower latency compared to older 8bit ESCs. This ESC also features a live telemetry connection for more advanced flight controllers, as well as a top of the line current sensor.

The Lumenier Razor LED ESC also includes 4x onboard RGB LEDs with a pre-programmed controller chip with an easy-press button. Simply press the button to cycle through all the LED color options and patterns. In addition this ESC is a distribution board for 4x more sets of LEDS that you can solder on to place on your drone's arms. All of the connected LEDs will by in sync with the on-board controller making it super simple for you. Changing all the LED colors on your drone is now as easy as a press of a button! (13 pre-programmed colors and patterns)

Not only does it have on-board LEDs, but the Razor LED ESC acts as it's own LED distribution board too! Hook up to 4 additional RGB LED strips for a super bright and colorful quad. The best part is the Razor LED ESC has an built in 5v regulator that powers all the LEDs for you in addition to sending the signal to each LED with the pre-programmed settings. All you have to do is press the button to cycle through all the cool effects.

Features

New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
Latest Gen. firmware using BLHeli_32 (Razor_32 target)
Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
Onboard RGB LEDs with controller and button + LED distribution system
Built in 5v regulator that powers the LED system
Adaptive timing, compatible with a wide range of motors and Kv
Synchronous rectification technology adds efficiency, damped light
Powerful regenerative braking / active braking.
2-6s LiPo battery compatible

Specs

Input: 2-6s LiPoly
Constant: 55 Amps
Burst: 65 Amps
Dimensions: 39x45x5mm
Mounting holes: 30.5x30.5 M4 (M3 with rubber inserts)
Signal wire: 7cm
Weight: 15g
8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4

Downloads

Includes

1x Lumenier Razor LED 55A 4in1 F3 BLHeli_32 2-6s ESC
1x 8pin micro JST-SH 7cm connector for 4in1 ESC to FC connection
1x 2200uF 35V Capacitor4x M3 Anti-vibration gummies (extra)

Videos

См. также

Стэки контроллер F7 + регулятор 4-в-1

Свежие скидки, купоны, новинки в наших каналах: