FlySky FS-SRM 2.4GHz ANT Receiver

FlySky FS-SRM 2.4GHz ANT Protocol Mini RC Receiver PWM/PPM/i-BUS/S.BUS Output Compatible FS-ST8 Radio Transmitter for RC FPV Racing Drone

OVERVIEW:

FS-SRM based on ANT protocol is a new receiver with two external antennas and bidirectional transmission. It outputs PWM or PPM/i-BUS/S.BUS signal and has a compact design. The design of the receiver is easily to install, and it adapts multicopters.

Specifications:

Brand Name: FlySky

Item Name: FS-SRM RC Receiver

Model: FS-SRM

Adaptive transmitters: Transmitter with ANT protocol, such as FS-ST8

Adaptive Models: Multicopters

Numbers of Channels: 1

RF: 2.4GHz ISM

Maximum Power: < 20dBm (e.i.r.p.) （EU）

2.4G Protocol: ANT

Resolution: 1024

Antenna: Two antennas

Distance: >380m

Input Power: 3.5 ~ 9V/DC

Data Output: PWM/PPM/i-BUS/S.BUS

Online Update: Yes

Temperature Range: -10℃ ~ +60℃

Humidity Limit: 20% ~ 95%

Dimensions: 19*12.1*3mm

Weight: 1.1g

Certifications: CE, FCC ID: 2A2UNSRM00

Binding:

The receiver supports two -way binding and one-way binding. The transmitter will display the information returned from the

receiver after the two-way binding is completed.

Follow the steps below to bind in two-way binding:

Select [2 WAY] for RF standard of the transmitter, then put the transmitter into bind mode.

The receiver supports tho ways to enter bind mode: BIND button binding and BIND button binding after power-on.

- BIND button binding: Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver

should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.

- BIND button binding after power-on: The receiver has not been connected to the transmitter when it is powered on. Press and

hold the BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode.

Then release the BIND button.

When the LED of the receiver is solid on, the binding process should be completed. The transmitter exits the bind mode

automaticlly.

Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any

problems arise.

Follow the steps below to bind in one-way binding:

Select [1 WAY] for RF standard of the transmitter, then put the transmitter into bind mode.

Put the receiver into bind mode ( Refer to the description above for entering bind mode).

When the LED of the receiver is in slow flashing state, the binding process should be completed. You need to manually put the

transmitter to exit the bind mode. Then the LED of the receiver is solid on, indicating that the binding is completed.

Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any probems arise.

Firmware update:

The firmware of this receiver is updated through the FlyskyAssistant (Only version 3.0 or above is supported. The firmware of

FlyskyAssistant is available on the Flysky official website).

This receiver can be updated via the following two ways:

After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the

computer, then open the FlyskyAssistant on the computer to update the firmware.

Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following

two ways (The LED of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on

the computer to update the firmware.

- Power on the receiver while pressing and holding the BIND button for more than ten seconds, until the LED of the receiver

operates in three-flash-one-off manner repeatedly, then release the BIND button.

- Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the

receiveroperates in three-flash-one-off manner repeatedly, then release the BIND button.

Package Included:

1 x FS-SRM RC Receiver