Eachine Tyro99 210mm PNP

Eachine Tyro99 210mm DIY Version FPV Racing RC Drone w/ F4 OSD 30A BLHeli_S 700TVL Camera 

Note:
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.
6. Take-off weight is about 450g.

Item	Specification
210mm Frame Kit	Wheel base: 210mm Frame arm thickness: 5mm Bottom plate thickness: 2mm Side plate thickness: 2mm Frame kit material: 3K carbon fiber & 6065 aluminium
2206 2150KV Brushless Motor	Motor KV: 2150RPM/V  Idle current (Io/10V): 1.26A Lipo cell: 3-5S Weight: 31g Max continuous current: 31A Max continuous power: 496W Max thrust: 1050g (4S/5") Configu-ration: 12N/14P Motor resistance (RM): 0.0572 Ω  Stator diameter: 22mm Stator thickness: 6mm Motor diameter: 27.7mm Motor body length: 19.2mm Overall shaft length: 34.2mm Prop adapter shaft: M5 Bolt holes spacing: 16mm Bolt thread: M3 Propeller: 5-6 inch
4 IN 1 30A BLHeli_S ESC	Continuous current: 30A Peak Current: 40A(10S) Input voltage: 2-5S BEC: 5V 2A BEC Main control chip: 48Mhz EFM8BB2 Firmware: BLHeli_S supports Dshot600 MOS: 5*6
Customized F4 Flight Controller	Main control chip: STM32F405 Sensor: ICM20602 6-axis Power supply: 5V Integrated OSD Onboard LC filter PID cycle rate & gyroscope refresh rate up to 32Khz Supports BetaFlight / inav racing firmware
700TVL CMOS Camera	Case size: 25mm*25mm Weight: 9.5g Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP) Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP) Signal system: PAL/NTSC switchable Resolution ratio(horizontal center): 700TVL Video output: 1.0Vp-p/75Ω Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB White balance: on/off optional  Exposure mode: electron exposure Electronic shutter: 1/50(1/60) - 1/100000 S Gamma correction: 0.45/1.0 Synchronization method: inter-sync Camera lens: standard 2.8mm Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V) Working current: 70mA (low power consumption) Working temperature: -20℃~-60℃ Humidity: 0%~98%
5.8G 40CH 0mW/25mw/200mw/600mw switchable VTX	Output power & transmission distance: ≥0.5km@25mW, ≥1km@200mW, ≥2km@600mW Transmitting power: 0mW/25mW/200mW/600mW Full video format: NTSC /PAL Input voltage & power dissipation: 7V~24V, +12V/260mA@600mW Size: 20*30*9mm Weight: ≤7g(except antenna) With output power self-check function. Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
Racerstar 5038 2 Blade Propeller	Material: PC Mounting hole: 5mm Center thickness: 8mm Quantity: 10 pairs Color: blue, red, yellow, purple, white Weight: 7.25G a pair    Delivery color randomly (10 pairs of propellers are the same color)
Battery	Not included Recommend 3-5S

Package Included:

1 x 210mm frame kit
2 x 2206 2150KV brushless motor CW
2 x 2206 2150KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x Customized F4 flight controller
1 x 700TVL CMOS camera

1 x 5.8G 40CH 0mw/25mw/200mw/600mw switchable VTX
2 x Battery strap
10 x Racerstar 5038 2 blade propeller CW
10 x Racerstar 5038 2 blade propeller CCW